View MT220WW01-VB_7838830.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

inno l u x display corporation mt220ww01 v.b lcd module specification ( ) preliminary specification ( ) final specification customer checked & approved by approved by checked by prepared by mkt qra td pd mkt innolux display corporation, no.160 kesyue rd., chu-nan site, hsinchu science park, chu-nan 350 , miao-li county, taiwan tel: 886-37-586000 fax: 886-37-586060 document number: mt220ww01 v.b-dr4-24(v04) www.jxlcd.com www.jxlcd.com free datasheet http:///
innolux copyright all rights reserved, copying forbidden. record of revision version revise date page content 1.0 2007/6/04 all initial release www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 3/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. contents: a. general specification b. electrical specifications 1. pin assignment 2. absolute maximum ratings 3. electrical characteristics a. typical operating conditions b. display color vs. input data signals c. input signal timing d. display position e. backlight driving conditions c. optical specifications d. reliability test items e. safety f. display quality g. handling precaution h. label i. mechanical drawings appendix www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 4/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. a. general specification no. item specification remark 1 display resolution (pixel) 1680(h) x 1050(v), wsxga+ resolution 2 active area (mm) 473.76(h) x 296.1(v) 3 screen size (inch) 22 inches diagonal 4 pixel pitch (mm) 0.282(h) x 0.282(v) 5 color configuration r, g, b vertical stripe 6 overall dimension (mm) 493.7 (w) x 320.1 (h) x 16.5 (d) (typ.) 7 weight (g) 2900 (max.) 8 surface treatment anti-glare, haze = 25%, hard coating (3h) 9 input color signal 8 bit lvds 10 display colors 16.7 m (6 bit with hi-frc) 11 optimum viewing direction 6 o?clock 12 backlight 4 ccfl 13 rohs rohs compliance www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 5/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. b. electrical specifications 1.pin assignment connector jae fi-xb30ssrl-hf16, foxconn gs23302-0311r-7f or mechanical interface equivalent connector. pin no. symbol description frame vss ground 1 rxino0- -lvds differential data input, chan 0-odd 2 rxino0+ +lvds differential data input, chan 0-odd 3 rxino1- -lvds differential data input, chan 1-odd 4 rxino1+ +lvds differential data input, chan 1-odd 5 rxino2- -lvds differential data input, chan 2-odd 6 rxino2+ +lvds differential data input, chan 2-odd 7 vss ground 8 rxoc- -lvds differential clock input (odd) 9 rxoc+ +lvds differential clock input (odd) 10 rxino3- -lvds differential data input, chan 3-odd 11 rxino3+ +lvds differential data input, chan 3-odd 12 rxine0- -lvds differential data input, chan 0-even 13 rxine0+ +lvds differential data input, chan 0-even 14 vss ground 15 rxine1- -lvds differential data input, chan 1-even 16 rxine1+ +lvds differential data input, chan 1-even 17 vss ground 18 rxine2- -lvds differential data input, chan 2-even 19 rxine2+ +lvds differential data input, chan 2-even 20 rxec- -lvds differential clock input (even) 21 rxec+ +lvds differential clock input (even) 22 rxine3- -lvds differential data input, chan 3-even 23 rxine3+ +lvds differential data input, chan 3-even 24 vss ground 25 vss ground 26 nc no connection 27 vss ground 28 vcc +5.0v power supply 29 vcc +5.0v power supply 30 vcc +5.0v power supply frame vss ground www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 6/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. #1 #30 #1 #30 #1 #30 rear view of lcm #1 #30 2. absolute maximum ratings note 1: the relative humidity must not exceed 90% non-condensing at temperatures of 40c or less. at temperatures greater than 40c, the wet bulb temperature must not exceed 39c. note 2: the unit should not be exposed to corrosive chemicals. values parameter symbol min. max. unit remark power voltage v cc -0.3 6 v at 25c input signal voltage v lh -0.3 4.3 v at 25c operating temperature top 0 50 c note 1 storage temperature t st - 20 60 c note 2 ccfl current icfl 3 8 [ma] www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 7/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. 3. electrical characteristics a. typical operating conditions note 1 : the specified current is under the v cc =5v, 25c, fv=60hz (frame frequency) condition whereas black pattern is displayed. note 2 : the specified current is under the vcc =5v, 25 c, fv=60hz (frame frequency) condition whereas white pattern is displayed. note 3 : the specified current is under the vcc =5v, 25 c, fv=60hz (frame frequency) condition whereas mosaic pattern(black & white [8*6] ) is displayed. white : 255 gray black : 0 gray item symbol min. typ. max. unit remark input voltage v cc 4.5 5 5.5 v permissive power input ripple v rf - - 0.25 v black i cc - 900 1400 note 1 white i cc - 700 - note 2 input current mosaic i cc - 800 - ma note 3 rush current i rush - - 4 a note 4 common mode voltage vcm - 1.2 - v differential input voltage vid 100 - 600 mv threshold voltage (high) vth - - 100 mv note 5 logic input voltage lvds: in+, in- threshold voltage (low) vtl -100 - - mv note 5 www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 8/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. note 4 : test condition : (1) v dd = 5 v, v dd rising time = 470 ? s 10% (2) pattern: mosaic pattern (3) test circuit note 5 : lvds signal definition vin + = positive differential data & clk input vin- = negative differential data & clk input vid = vin + ? vin- , ? vcm = x vcm + ?vcm- x , ? vid = x vid + ?vid- x , vid+ = x vih + ?vih- x , vid- = x vil + ?vil- x , vcm = (vin + +vin-)/2, vcm+ = (vih + +vih-)/2, vcm- = (vil + +vil-)/2, 90 % ton=470 ? s ? 10% v dd m2 m1 1k c3 47k r1 c1 5 v 12v vdd ( lcd input) control signal (high to low) 2sk1399 2sk1059 r2 c2 10000pf 1uf r3 47k fuse 1uf www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 9/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. note 6 : power on sequence for lcd v dd parameter value unit min. typ. max. ms t1 0.1 -- 10 ms t2 0 -- 50 ms t3 200 250 -- ms t4 100 250 -- ms t5 0 20 50 ms t6 0.1 -- -- ms t7 1000 -- -- ms www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 10/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. b. display color vs . input data signals the brightness of each primary color (red, green and blue ) is based on the 8-bit gray scale data input for the color; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. color input color data red green blue msb lsb msb lsb msb lsb r7 r6 r5 r4 r3 r2 r1 r0 0 1 0 0 0 1 1 1 black red(255) green(255) blue(255) cyan magenta yellow white 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 basic colors 0 0 0 : 1 1 1 red(000) dark red(001) red(002) : red(253) red(254) red(255) bright 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 red 0 0 0 : 0 0 0 green(000)dark green(001) green(002) : green(253) green(254) green(255) bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 green 0 0 0 : 0 0 0 blue(000) dark blue(001) blue(002) : blue(253) blue(254) blue(255) bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 blue 0 1 0 0 0 1 1 1 0 0 1 : 0 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 g7 g6 g5 g4 g3 g2 g1 g0 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 11/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. c. input signal timing support input timing table the input signal timing specifications are sh own as the following table and timing diagram. signal item description min. typ. max. unit period 12.2 16.8 21.23 ns clock dclk frequency 47.1 59.6 82 mhz t v_total v total line number 1059 1080 1100 t h t v_data data duration 1050 1050 1050 t h t vb v-blank 9 30 50 t h vertical f v frequency 50 60 76 hz t h_total h total pixel number 890 920 1004 dclk t h_data data duration 840 840 840 dclk horizontal t hb h-blank 73 80 164 dclk note: because this module is operated by de only mode, hsync and vsync input signals should be set to low logic level or ground. otherwise, this module would operate abnormally. input signal timing diagram tv tvd tvb th tc thb thd de dclk de data www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 12/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. d. display position d(1, 1) d(2, 1) ?? d(840, 1) ?? d(1679, 1) d(1680, 1) d(1, 2) d(2, 2) ?? d(840, 2) ?? d(1679, 2) d(1680, 2) . . . ?? . . . ?? . . . . . . d(1, 525) d(2, 525) ?? d(840, 525) ?? d(1679, 525) d(1680, 525) . . . ?? . . . ?? . . . . . . d(1, 1049) d(2, 1049) ?? d(840, 1049) ?? d(1679, 1049) d(1680, 1049) d(1, 1050) d(2,1050) ?? d(840, 1050) ?? d(1679,1050) d(1680, 1050) e. backlight driving conditions parameter symbol min. typ. max. unit remark remark lamp voltage vl 680(8ma) 794(7ma) 955(3ma) vrms -- note 1, 2 lamp operation current il 3 7 8 marms -- note 3 1250 t = 25 $ note 4,5,6,7 lamp starting voltage vlstart 1570 vrms t = 0 $ note 4,5,6,7 frequency f 40 55 60 khz note 7 lamp life time 40000 50000 hr note 8 note: the waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. the performance of the backlight, such as lifetime or brightness, is greatly influenc ed by the characteristics of the dc-ac inverter for the lamp. all the parameters of an inverter should be carefully designed to avoid producing too much current leakage from high voltage output of the inverter. when designing or ordering the inverter please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. if the above situation is confirmed, the module should be operated in the same manners when it is installed in your instrument. note 1 : specified values are for a single lamp. note 2: operating voltage is measured at 25 2 o c. the variance of the voltage is 10%. note 3: the degree of unbalance: less than 10% the ratio of wave height: less than 10% 2 the degree of unbalance = | i p - i -p | /irms*100(%) the ratio of wave height = i p (or i -p )/irms lamp should be completely turned on. i p i -p i p : high side peak i -p : low side peak www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 13/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. note 4: test equipment: as-114b note 5 : the voltage shown above should be applied to the lamp for more than 1 second after startup. otherwise, the lamp may not be turned on normally. note 6: inverter should provide more than max. value, and then lamp could be completely turned on. note 7: lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. lamp hi-pot test spec: the current leakage should not be more than (<=) 0.9ma under the conditions of ?the frequency of the inverter output voltage keeping 60hz, test voltage keeping 3.0kv and test time keeping 2sec?. note 8: lamp life definition: the brightness of la mp becomes 50% of the initial brightness or not normal lighting. backlight connector : 35001hs-02l pin no. symbol function remark 1 vih lamp high voltage input cable color: pink 2 vil lamp low voltage input cable color: white 3 vih lamp high voltage input cable color: blue 4 vil lamp low voltage input cable color: black www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 14/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. c. optical specifications specification item symbol condition min. typ. max. unit remark tr 1.5 3 tf 3.5 7 response time tr+tf = 0 5 10 ms note 4 contrast ratio cr = 0 500 700 note 3,5 top cr 10 cr 5 70 75 80 85 bottom cr 10 cr 5 70 75 80 85 left cr 10 cr 5 75 80 85 89 viewing angle right cr 10 cr 5 75 80 85 89 deg. note 3,5,7 brightness (center) yl 200 250 nit note 3,6 wx 0.313 wy 0.329 rx 0.640 ry 0.349 gx 0.284 gy 0.617 bx 0.142 color chromaticity(cie) by = 0 -0.03 0.067 +0.03 note 3 white uniformity (9 points) w 0.75 0.80 note 3,8 cross talk ct 2% note 9 note 1: ambient temperature = 25c. note 2: to be measured in dark room after backlight warm up 30 minutes. note 3: to be measured with a viewing cone of 2by topcon luminance meter bm-5a. note 4: definition of response time: the output signals of bm-7 are measured when the input signals are changed from ?black? to ?white? (fa lling time) and from ?white? to ?black? (rising time), respectively. the response time interv al is between the 10% and 90% of amplitudes. refer to figure as below : www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 15/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. note 5: definition of contrast ratio: contrast ratio is calculated by the following formula. note 6: driving conditions for ccfl: i l = 7ma, 50 khz frequency. note 7: definition of viewing angle. note 8: definition white uniformity: luminance are measured at the following nine points (p1~p9). s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% contrast ratio ( cr ) = brightness on the "white" state brightness on the "black" state ? w = minimum brightness o f nine points ( p1~p9 ) . maximum brightness of nine points (p1~p9). www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page 16/22 all rights reserved any portion of this document shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. field=2 ? 50cm photo-detector (bm-5a) lcd panel note 9: l l a -l a? l / l a x 100%= 2% max., l a and l a? are brightness at location a and a? l l b -l b? l / l b x 100%= 2% max., l b and l b? are brightness at location b and b? note 10: optical characteristic measurement setup. 0 gray level 1/2 1/2 1/6 1/6 a b 1/2 1/2 1/6 1/6 2/3 1/3 1/3 2/3 a? b? 127 gray level 127 gray level www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page : 17/22 all rights reserved any portion of this documen t shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. d. reliability test items test item test condition judgment remark high temperature storage 60c, 240hrs note 1 note 2 low temperature storage -20c, 240hrs note 1 note 2 high temperature & high humidity operation 40c, 90%rh, 240hrs (no condensation) note 1 note 2 high temperature operation 50c, 240hrs note 1 note 2 low temperature operation 0c, 240hrs note 1 note 2 thermal shock (non-operation) -20c~60c 1hr, 5mins, 1hr, 100cycles note 1 note 2 electrostatic discharge (esd) (non-operation) contact:+/-8kv, 150pf(330ohms), 10 times/1 point, 1 time/1 sec air discharge:+/-15kv, 150pf(330ohms), 10 times/1 point, 1 time/1 sec note 1 note 2 vibration (non-operation) vibration level : 1.5g bandwidth : 10-300hz waveform : sine wave, sweep rate : 10min 30 min for each direction x, y, z (1.5 hrs in total) note 1 note 2 mechanical shock (non-operation) shock level : 50g, 11ms waveform : half sine wave direction : x, y, z one time each direction note 1 note 2 mtbf demonstration 40,000 hours with confidence level 90% note 1 note 3 note1: pass: normal display image with no obvious non-uniformity and no line defect. partial transformation of the module parts should be ignored. fail: no display image, obvious non-uniformity, or line defects. note2: evaluation should be tested after stor age at room temperature for one hour. note 3 : the mtbf (exclude the ccfl ) calculation is based on the assumption that the failure rate distribution meets the exponential model. www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page : 18/22 all rights reserved any portion of this documen t shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. e. safety 1. sharp edge requirements there will be no sharp edges or corners on the display assembly that could cause injury. 2. materials a. toxicity there will be no carcinogenic materials used anywhere in the display module. if toxic materials are used, they will be reviewed and approved by the responsible innolux toxicologist. b. flammability all components including electrical components that do not meet the flammability grade ul94-v1 in the module will complete the flammability rating exception approval process. the printed circuit board will be made from material rated 94-v1 or better. the actual ul flammability rating will be printed on the printed circuit board. c. capacitors if any polarized capacitors are used in the di splay assembly, provisions will be made to keep them from being inserted backwards. f. display quality the display quality of the color tft-lcd module should be in compliance with the innolux?s incoming inspection standard. g. handling precaution the handling of the tft-lcd should be in comp liance with the innolux?s handling principle standard. www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page : 19/22 all rights reserved any portion of this documen t shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. h. label 1. module label (a) model number: mt220ww01 (b) version: v.b (c) serial id i: z 1 z 2 z 3 z 4 z 5 z 6 z 7 z 8 z 9 z 10 z 11 z 12 serial id includes the information as below: 1. manufactured date: year: 0~9, for 2000~2009 2. month: 1~9 & a~c for jan.~dec. 3. date: 1~9 & a~z (exclude i, o, q, u) for 1th~31th 4. code of grade: 1, 2, 3, 5, e 5. serial no.: module manufacture sequence number. (d) serial id ii (inl internal use) serial no. code of grade year, month, date inl internal use inl internal use inl internal use mt220ww01 am2200001 v.b b0x made in xxx z 1 z 2 z 3 z 4 z 5 z 6 ? z 7 ? z 8 z 9 z 10 z 11 z 12 18 mm z 1 z 2 ? z 3 z 4 z 5 z 6 z 7 ? z 8 ? z 9 ? z 10 ? z 11 z 12 ? z 13 ? z 14 z 15 ? z 16 ? z 17 z 18 z 19 ? z 20 z 21 z 22 z 23 73 mm www.jxlcd.com www.jxlcd.com free datasheet http:///
spec no. mt220ww01 v.b page : 20/22 all rights reserved any portion of this documen t shall not be reproduced, copied, or transformed to any other forms without prior written pe rmission from innolux display corporation. 2. carton label 60 mm (a) model number: mt220ww01 (b) version: v.0 (c) packing quantity: 5 pcs (d) serial id: z 1 z 2 z 3 z 4 z 5 z 6 z 7 z 8 z 9 serial id includes the information as below : (a) manufactured date: year: 0~9, for 2000~2009 month: 1~9 & a~c for jan.~dec. date: 1~9 & a~z (exclude i, o, q, u) for 1th~31th (b) code of grade: 1, 2, 3, 5, e (c) serial no.: module packing sequence number. innolux display box id : z 1 z 2 z 3 z 4 -- z 5 -- z 6 z 7 z 8 z 9 model no. mt220ww01 v.b am 2200001 b0x quantity : 5 pcs mfg date: 20xx/xx/xx made in xxx qc: 100 mm serial no. code of grade year, month, date inl internal use www.jxlcd.com www.jxlcd.com free datasheet http:///
www.jxlcd.com www.jxlcd.com free datasheet http:///
www.jxlcd.com www.jxlcd.com free datasheet http:///

▲Up To Search▲

Price & Availability of MT220WW01-VB

	To Download MT220WW01-VB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .